Contacts

Download the new electrical safety certificate form. Electrical safety certificate II, III, IV and V tolerance groups. Description of identity pages

  • 29.04.2020

In October 2016, new rules on electrical safety come into force, or rather, changes in Order 325n.

No sooner had the new rules on electrical safety come into force (what is 2 years), as others come out that radically change the concept.
I don’t know how they will help in the safety of work, but the bureaucratic foundations have been shaken.
You can download Order No. 74n dated February 19, 2016 on changes to the new electrical safety rules 2016.
By and large, in the Order, some designations have been replaced with others (I’ll never know how this will affect security), although a very significant change in my opinion is appearance electrical safety certificates have changed radically.

You can download the new electrical safety rules with changes from 10/19/2016

Electrical safety certificate of a new sample

The appearance of the certificate remained unchanged. Vinyl Coated Cardboard Base The color of the vinyl is irrelevant, but cherry is preferred. The size is also 95x65 mm.
On the front side, the word "Certificate" is embossed in gold or white paint.
But the content has changed a lot.

Below I have given two examples of certificates issued by educational institutions with which we cooperate. Both have minor differences, but they completely correspond to the established model (Appendix 2 to Order 74n).

I Option:

1 page contains:

Certificate number (usually this is a serial number in the electrical safety knowledge check log);
Name structural unit(if any);
Date of issue of the certificate;
Photo and place of seal of the organization for which electrical safety was issued (energy consuming companies do not need Appendix 2, clause 10)

2 page:
Full name of the owner of the "crust";
Position held;
Assigned personnel (operational, maintenance, etc.)
Employer's (or responsible person's) signature
Seal of the organization for which the permit was issued.

3 page contains the results of the knowledge test (assigned group, date of the test, signature of the inspector, etc.)


4, 5 and 6 pages- are necessary only for energy companies (we will not consider).

7 page- Prom safety and other standards.

8 page- Access to special work.


II Option:


And this is how they are approximately filled (taken from another site):


Those who are looking for where to download the new 2016 electrical safety certificate form can do this (for those who do not want to buy forms, but want to print and assemble them themselves).

Let me answer two basic questions:
1. For energy-consuming companies, it is not necessary to paste a photo (Appendix 2, clause 10);
2. The employees kindly answered my request to Supervision "Do I need to recertify with the release of new rules" (the request was in June, they answered in October 2 weeks before the entry), the screen was posted below:


In my opinion, the answer was strangely veiled, but as far as I understood, the most important thing is that you don’t need to urgently run and change your certificate, unless at the request of the head, and then only after October 19th.

And here is what the supervisory representative answered on the issue of issuing electrical safety certificates according to the new rules (3-minute video, the quality is not important, the sound is ahead of the video, but the meaning is clear).
It is especially recommended to pay attention to the last 30 seconds.


Here is what supervisors answered the question "Who urgently needs to undergo an extraordinary knowledge test"

(Taken from the Rossnadzor website)

Well, now about the changes themselves (personal opinion of the author).

1. To begin with, clause 1.1 has undergone a change
It was:
The rules on labor protection during the operation of electrical installations (hereinafter referred to as the Rules) apply to employees from among electrical, electrical and non-electrotechnical personnel, as well as to employers (physical and legal entities, regardless of the form of ownership and organizational and legal forms), employed maintenance electrical installations conducting in them operational switching organizing and performing construction, installation, commissioning, repair work, testing and measurement.

It became:
Rules on labor protection during the operation of electrical installations (hereinafter referred to as the Rules) establish state regulatory requirements for labor protection during the operation of electrical installations.
The requirements of the Rules apply to employers - legal and individuals regardless of their organizational and legal forms and employees from among the electrical, electrical and non-electrotechnical personnel of organizations (hereinafter referred to as employees) engaged in the maintenance of electrical installations, conducting operational switching in them, organizing and performing construction, installation, commissioning, repair work, testing and measurement , as well as managing the technological modes of operation of electric power facilities and power-receiving installations of consumers.
Safety requirements for the operation of specialized electrical installations, including contact network electrified railways, urban electric transport must comply with the Rules, taking into account the features of operation, due to the design of these electrical installations.

I agree, the additions are very important ... let's see how it will affect the workflow.

2. Clause 2.4
It was:
Employees related to electrical personnel, as well as electrical technological personnel, must pass a test of knowledge of the Rules and other regulatory and technical documents (rules and instructions for the installation of electrical installations, for the technical operation of electrical installations, as well as the use of protective equipment) within the limits of the requirements for relevant position or profession, and have an appropriate electrical safety group, the requirements for which are provided for in Appendix No. 1 to the Rules.

It became:
Employees related to electrical and electrical engineering personnel, as well as state inspectors who monitor and supervise compliance with safety requirements during the operation of electrical installations, labor protection specialists who control electrical installations, must pass an examination of knowledge of the requirements of the Rules and other safety requirements for the organization and implementation work in electrical installations within the requirements for the relevant position or profession, and have an appropriate electrical safety group, the requirements for which are provided for in Appendix No. 1 to the Rules.
The requirements of the Rules established for employees from among the electrical personnel are also mandatory for employees from among the electrical technological personnel.

3. Affected (or supplemented, as anyone likes) paragraph 2 of paragraph 2.5:
It was:
An employee who has passed the knowledge test on labor protection during the operation of electrical installations is issued a certificate of knowledge of labor standards and rules for working in electrical installations, the form of which is provided for in Annexes No. 2, 3 to the Rules.

It became:
The employees specified in paragraph 2.4 of the Rules and who have passed the knowledge test of the requirements of the Rules and other safety requirements for the organization and performance of work in electrical installations are issued certificates of knowledge of the rules for working in electrical installations, the forms of which are provided for in Annexes No. 2, 3 to the Rules.

4. In the third paragraph, "steeman's work" was excluded in clause 2.6.

It became:
To special work relate:
work performed at a height of more than 5 m from the ground, ceiling or working platform, on which work is carried out directly from structures or equipment during their installation or repair with the obligatory use of fall protection equipment.

Interestingly, climbing work in general is no longer related to electrical safety? Or will the height tolerance be enough?

5. . Paragraph 3.1 should now read as follows:
It was:
Operational switching should be performed by employees who carry out operational management and maintenance of electrical installations (inspection, operational switching, preparation of the workplace, admission and supervision of workers, performance of work in the order of current operation) (hereinafter referred to as operational personnel), or employees specially trained and trained for operational maintenance in the approved volume of electrical installations assigned to it (hereinafter - operational - repair personnel), organizations or separate subdivision.

It became:
Operational maintenance and inspection of electrical installations must be carried out by employees of the subject of the electric power industry (consumer of electric energy), authorized by the subject of the electric power industry (consumer of electric energy) to carry out, in the prescribed manner, actions to change the technological mode of operation and the operational state of power lines, equipment and devices with the right to directly affect the organs control of equipment and devices of relay protection and automation in the implementation of operational and technological control, including using remote control facilities, on objects of the electric power industry (power-receiving installations) owned by such a subject of the electric power industry (consumer of electric energy) on the right of ownership or on other legal grounds, or in cases established by law - at electric power facilities and power receiving installations owned by third parties, as well as coordination of these activities actions (hereinafter referred to as operational personnel), or employees from among the repair personnel with the right to directly influence the controls of equipment and relay protection and automation devices that carry out operational maintenance of electrical installations assigned to them (hereinafter referred to as operational and repair personnel).
In the Rules, operating personnel is also understood as operating and maintenance personnel, if there are no special requirements for them.

6. Paragraph 3.4 is now stated as follows
It was:
Sole inspection of the electrical installation, electrical part technological equipment has the right to perform an employee, from among the operational personnel, having a group of at least III, serving this electrical installation in working time or on duty, or an employee from among the administrative and technical personnel (managers and specialists who are entrusted with the responsibility for organizing technical and operational maintenance, carrying out repair, installation and adjustment work in electrical installations (hereinafter referred to as administrative and technical personnel), having group V - for electrical installations with voltages above 1000 V and an employee who has group IV - for electrical installations with voltages up to 1000 V. The right of a sole inspection is granted on the basis of the ORD of the organization (separate subdivision).

It became:
A sole inspection of the electrical installation, the electrical part of the technological equipment has the right to be performed by an employee from among the operational personnel, having a group of at least III, operating this electrical installation, who is on duty, or an employee from among the administrative and technical personnel (managers and specialists), who is entrusted with the duties for the organization of technical and operational maintenance, repair, installation and adjustment work in electrical installations (hereinafter referred to as administrative and technical personnel (managers and specialists)), having:
group V - when operating an electrical installation with a voltage above 1000 V;
group IV - when operating an electrical installation with a voltage of up to 1000 V. The right of a sole inspection is granted on the basis of the organization's (separate subdivision) OSD.
Inspection of overhead power lines (devices for transmitting electricity through wires located on outdoors attached with the help of insulators and fittings to supports or brackets and posts on engineering structures (bridges, overpasses) (hereinafter - VL) must be carried out in accordance with the requirements of paragraphs 7.15, 38.73, 38.74, 38.75 of the Rules. For the beginning and end of the overhead line, linear portals or linear inputs of an electrical installation are accepted, which serve to receive and distribute electricity and contain switching devices, prefabricated and connecting buses, auxiliary devices (compressor, battery), as well as protection devices, automation and measuring instruments (hereinafter referred to as distribution devices, switchgear), and for branches - a branch support and a linear portal or a linear input of a switchgear.
RU are:
open switchgear (hereinafter - outdoor switchgear), the main equipment of which is located in the open air;
closed switchgear (hereinafter - ZRU), the equipment of which is located in the building.

7. Paragraphs 3.13, 5.7, 8.1, 14.3, 21.8, 46.6 were also affected by the change, but already in the case relation of administrative technical personnel
It was:
"administrative and technical staff"

It became:
administrative and technical personnel (executives and specialists) "in the appropriate cases. (Looks like an electrician was born who was assigned administrative staff). Although sometimes such an explanation is not superfluous.

8. Paragraph 4.4 now reads as follows
It was:
Overhaul of electrical equipment with voltages above 1000 V, work on live parts without removing voltage in electrical installations with voltages above 1000 V, as well as repair of overhead lines, regardless of voltage, must be carried out according to technological maps or a project for the production of works (hereinafter - PPR), approved by the head of the organization.
Work on lines under induced voltage (disconnected overhead lines, overhead communication lines (hereinafter - VLS), on lines for the transmission of electricity, consisting of sections in the air and cable version, interconnected (hereinafter - KVL), which run along the entire length of the line or in separate sections near overhead lines with a voltage of 6 kV and above or near an electrified contact network railway alternating current, which are under operating voltage, on the wires (cables) of which, with various grounding schemes (as well as in the absence of grounding), at the highest operating current of the influencing overhead lines, a voltage of more than 25 V is induced, as well as all overhead lines built on double-circuit (multi-circuit) supports when at least one circuit with a voltage of 6 kV and higher (hereinafter - overhead lines under induced voltage) is turned on, they are carried out according to the PPR for the work performed according to the tolerance.

It became:
Overhaul of electrical equipment with voltages above 1000 V, work on current-carrying parts without removing voltage in electrical installations with voltages above 1000 V, as well as repair of overhead lines, regardless of voltage, must be carried out according to technological maps or a project for the production of works (hereinafter referred to as PPR), approved by the head of the organization (separate divisions).
Work on lines under induced voltage (VL, KBL, VLS, air sections of KBL, which run along the entire length or in separate sections near existing overhead lines or the contact network of an electrified AC railway, on disconnected wires (cables) of which, when grounding the line at the ends (in the switchgear) in its individual sections, a voltage of more than 25 V is maintained at the highest operating current of the influencing overhead lines (when converted to the highest operating current of the influencing overhead lines), are carried out according to technological maps or PPR approved by the head of the organization (separate subdivision).

9. Clause 4.17 appeared with the following content:
4.17. On overhead lines and overhead lines, before connecting or breaking electrically connected sections (wires, cables), it is necessary to equalize the potentials of these sections. The potential equalization of the sections of VL, BLS is carried out by connecting these sections with a conductor or by installing groundings on both sides of the gap (probable gap) with connection to one grounding conductor (grounding device).
In my opinion, this is a really important point.


10. In clause 5.1, paragraphs 2 and 3 have been changed:
It was:
registration of an order, order or list of works performed in the order of current operation;
issuance of a permit for the preparation of the workplace and for admission to work in cases specified in paragraph 5.14 of the Rules;

It became:
registration of work by an order, order or list of works performed in the order of current operation;
issuance of a permit for the preparation of the workplace and for admission to work, taking into account the requirements of paragraph 5.14 of the Rules.

11. Has undergone changes and clause 5.2, paragraph 3:
It was:
Employees responsible for the safe conduct of work in electrical installations are:



allowing;
work producer;
watching;
brigade members.
It became:

Employees responsible for the safe conduct of work in electrical installations are:
issuing the order, giving the order, approving the list of works performed in the order of current operation;
"issuing a permit for the preparation of the workplace and for admission, taking into account the requirements of paragraph 5.14 of the Rules;".
responsible work manager;
allowing;
work producer;
watching;
brigade members.

12. Paragraphs 5.3 - 5.6 should now read as follows:
It was:
5.3. The worker issuing the order, giving the order determines the need and possibility safe execution work. He is responsible for the sufficiency and correctness of the safety measures indicated in the work order (order), for the qualitative and quantitative composition of the team consisting of two or more employees, including the work foreman, and for the appointment of those responsible for the safety of the work, for the compliance of the work performed with the groups of workers listed in the work order , as well as conducting targeted briefing to the responsible work manager (work supervisor, supervisor).
5.4. The right to issue orders and orders is granted to employees from among the administrative and technical personnel of the organization who have group V - in electrical installations with voltages above 1000 V and group IV - in electrical installations with voltages up to 1000 V.
In the absence of employees with the right to issue orders and orders, when working to prevent accidents or eliminate their consequences, it is allowed to issue orders and orders from among the operational personnel who have group IV. Granting to operational personnel the right to issue orders and orders must be formalized in writing by the head of the organization.
5.5. The employee issuing a permit for the preparation of workplaces and for admission to work in electrical installations is responsible:
for giving commands to disconnect and ground equipment and obtain confirmation of their implementation, as well as independent actions to disconnect and ground equipment in accordance with the measures for preparing the workplace, determined by the order (order) taking into account the actual diagram of electrical installations and the electrical network;
for the ability to safely disconnect, turn on and ground the equipment under its control;
for coordinating the time and place of brigades allowed to work in electrical installations, including accounting for brigades, obtaining information from all brigades (allowing) admitted to work in electrical installations about the complete completion of work and the possibility of putting the electrical installation into operation;
for the correctness of these commands, independent actions to turn on the switching devices in terms of excluding the supply of voltage to the workplaces of authorized teams.
5.6. The right to issue permits for the preparation of workplaces and admission to work at electric grid facilities is granted to operational personnel with group IV-V in accordance with job descriptions and distribution of equipment according to the methods of operational management.
It is allowed to grant the right to issue permits for the preparation of jobs and access to work at electric grid facilities to employees from among the administrative and technical personnel authorized to do so by a written instruction from the head (manager) of the operating organization (separate subdivision) in the operation of electrical installations that are in the operational management of other subjects of the electric power industry.


It became:

5.3. The employee issuing the order, giving the order, determines the need and possibility of safe work. He is responsible for the sufficiency and correctness of the security measures indicated in the order (order); for the qualitative and quantitative composition of the team and the appointment of those responsible for the safe performance of work; for the compliance of the electrical safety groups of employees specified in the work order with the work performed; for conducting targeted briefing to the responsible work manager (work foreman, supervisor).
5.4. The right to issue orders and orders is granted to employees from among the administrative and technical personnel (managers and specialists) who have group V (when operating electrical installations with voltages above 1000 V), group IV (when operating electrical installations with voltages up to 1000 V).
In the absence of workers entitled to issue orders and orders, during work to prevent accidents or eliminate their consequences, it is allowed to issue orders and orders from among the operational personnel who have group IV, located directly on the territory of the electric power facility or the power receiving installation of the consumer of electricity. Granting to operational personnel the right to issue orders and orders must be formalized by the ORD of an organization or a separate subdivision.
5.5. The employee issuing a permit for the preparation of jobs and for admission, answers:
for issuing commands for disconnecting and grounding power transmission lines and equipment located in it technological management and obtaining confirmation of their implementation, as well as for independent actions to disconnect and ground power lines and equipment under its technological control;
for the compliance and sufficiency of the measures provided for by the order (order) for disconnecting and grounding equipment, taking into account the actual scheme of electrical installations;
for coordinating the time and place of work of authorized teams, including for accounting for teams, as well as for obtaining information from all teams (allowing) admitted to work in the electrical installation about the complete completion of work and the possibility of putting the electrical installation into operation.
In the event that the employee issuing the permit for the preparation of workplaces and for admission is not a person in whose technological control the power transmission line and equipment are located, the specified employee is responsible for obtaining confirmation of the completed technical measures for disconnecting and grounding the power transmission line and equipment from the dispatching personnel (employee of the subject of operational dispatch control in the electric power industry (dispatcher), authorized in the implementation of operational dispatch control in the electric power industry, on behalf of the subject of operational dispatch control in the electric power industry, to issue dispatch commands and permits that are mandatory for execution or to change the technological mode of operation and the operational state of dispatching objects, directly influencing on them using remote control means, when managing the electric power regime of the power system) or operational personnel, in whose dispatching room or technol Power lines and equipment are under logical control.
5.6. The right to issue permits for the preparation of workplaces and for admission is granted to operational personnel with a group of at least IV, in accordance with job descriptions.
It is allowed to issue permits for the preparation of workplaces and grant access to employees from among the administrative and technical personnel (managers and specialists) with a group of at least IV, authorized to do so by the ORD of an organization or a separate subdivision.


A few significant changes, but not for us to judge ...

13. The abbreviation SDTU in paragraph 5.7 was deciphered for those who do not understand.
Something like this: on equipment and installations of communication facilities, "dispatching and technological control facilities (hereinafter referred to as SDTU)" ... ..


14. Item 5.14 will now sound like this:
It was:
The issuance of a permit for the preparation of a workplace and admission are carried out if it is necessary to perform disconnections and grounding of electrical installations related to electric grid facilities, operated by electric power industry entities or other owners, in respect of which operational management is carried out when providing services for the transmission of electrical energy to consumers.

It became:
The requirements for the appointment of a person responsible for issuing a permit for the preparation of workplaces and for admission, and for the issuance of such a permit do not apply to the performance of work in electrical installations of consumers of electric energy, except for work on overhead lines, cable lines, and cable lines that require coordination by the personnel of another organization when change in their operational status.

A very "significant" change.

15. Paragraphs two and three of clause 6.1 shall be stated as follows:
In paragraph 6.1, the second and third paragraphs will now sound like this
It was:
In cases where the foreman is appointed at the same time as allowing, the order, regardless of the method of its transfer, is filled in two copies, one of which remains with the issuer of the order.
Depending on local conditions (location of the control room), one copy of the order remains with the employee who issues the permit for the preparation of the workplace and the permit (of the dispatcher).

It became:
In cases where the foreman is appointed at the same time as allowing, the order, regardless of the method of its transfer, is filled in two copies, one of which remains with the issuer of the order.
Depending on local conditions, one copy of the order may be transferred to an employee from among the operational personnel who issues permission to prepare the workplace and for admission.

From changing the places of the terms ...

16. And in paragraph 6.17, on the contrary, "means of dispatching and technological control (hereinafter referred to as SDTU)" were encrypted in "SDTU".


17. We state clause 7.7 as follows:
It was:
When carrying out work, the foreman (supervisor) from among the operational personnel performing work or monitoring those working in electrical installations with voltages above 1000 V must have group IV, and in electrical installations with voltages up to 1000 V - group III. Team members working in electrical installations with voltage up to and above 1000 V must have group III.
Admission to work in electrical installations must be carried out after the implementation of technical measures for the preparation of the workplace, determined by the employee issuing the order.

It became:
When carrying out urgent work, the foreman (supervisor) from among the operational personnel performing work or monitoring those working in electrical installations with voltages above 1000 V must have group IV, and in electrical installations with voltages up to 1000 V - group III. Team members working in electrical installations with voltage up to and above 1000 V must have group III.
Admission to work in electrical installations must be carried out after the implementation of technical measures for the preparation of the workplace, determined by the employee issuing the order.

It is not clear what has changed, well, the authorities know better ...

18. In paragraph 7.15, the first paragraph will now read as follows:
It was:
One employee with group II is allowed to perform the following work by order:

It became:
One employee with group II is allowed to perform the following work on the overhead line by order:

Added Air Lines...

19. In paragraph 2 of clause 17.2, the following changes
It was:
In the absence of a visible break, in prefabricated switchgears with withdrawable elements, as well as in complete switchgears with SF6 insulation (hereinafter referred to as GIS) with a voltage of 35 kV and higher, it is allowed to check the disconnected position of the switching device by checking the mechanical indicator of the guaranteed position of the contacts.

It became:
In the absence of a visible break in prefabricated switchgears with withdrawable elements, as well as in complete switchgears with SF6 insulation (hereinafter referred to as GIS) with a voltage of 6 kV and higher, it is allowed to check the off position of the switching device by checking the mechanical indicator of the guaranteed position of the contacts.

20. In paragraph 18.2
It was:
On the drives of switching devices, which are disabled for the work of overhead lines or cable lines, regardless of the number of working teams, one poster "Do not turn on! Work on the line" is posted. At remote control switching devices with workstations, the sign of the prohibition poster “Do not turn on! Work on the line! is displayed on the diagram next to the symbol of the switching device, which supplies voltage to the overhead line or cable. This poster is hung out and removed at the direction of the operational personnel who keep records of the number of brigades working on the line.

It became:
On the drives of the disconnectors, which are turned off to perform work on the overhead line, cable line or cable line, one poster "Do not turn it on! Work on the line" is posted, regardless of the number of working teams. When remotely controlling switching devices with workstations, the sign of the prohibition poster "Do not turn it on! Work on the line!" should be displayed on the diagram next to the symbol of the disconnector that supplies voltage to the power line. In the absence of disconnectors on power lines with voltage up to 1000 V, it is allowed to hang out a poster "Do not turn it on! Work on the line!" on drives or keys for controlling the switching device, depending on its design.
The poster is hung out and removed at the command of the dispatching or operational personnel, in whose dispatching or technological control, respectively, is the overhead line, overhead line or cable line. Before issuing the command to remove the poster "Do not turn on! Work on the line!" dispatching or operational personnel, in whose dispatching or technological control, respectively, the overhead line, overhead line or cable is located, must receive from an employee from among the operational personnel issuing permission to prepare the workplace and for admission, confirmation of the completion of work and the removal of all teams from the workplace.

21 In paragraph 19.3, the first and second paragraphs read as follows:
It was:
It is allowed to check the absence of voltage by reconciling the circuit in kind:
in open switchgear, switchgear and at a complete transformer substation (hereinafter - KTP) for outdoor installation, as well as on overhead lines in case of fog, rain, snowfall in the absence of special voltage indicators;

It became:
It is allowed to check the absence of voltage by reconciling the circuit in kind:
in outdoor switchgear and at a complete transformer substation (hereinafter referred to as KTP) for outdoor installation, as well as on overhead lines in case of fog, rain, snowfall in the absence of special voltage indicators;

22. In paragraphs 38.6, 38.88, 41.40, the word "climbing work" is replaced by "work performed at a height of more than 5 m from the ground, ceiling or working platform, on which work is carried out directly from structures or equipment during their installation or repair with mandatory use of fall protection equipment" in the appropriate case.


23. Amended from 38.43 to 38.48

Certificate for consumers of electricity (clause 10 of Order No. 74n dated February 19, 2016: "... In the certificate for consumers of electrical energy, the presence of the fourth, fifth and sixth pages, as well as the mandatory presence of a photograph, is not required).

Electrical safety certificate (new) order 74-n dated February 19, 2016 for consumers of electrical energy

Electrical safety certificate (new) order 74-n dated 02/19/2016 for electricity suppliers

Sample form of electrical safety certificate

In the photo you see the form of the certificate in the prescribed form.

Filling out the electrical safety certificate form

You can get a free consultation on filling out the certificate form from us.

Do you want to buy an electrical safety certificate in Samara?

We sell forms of certificates made according to the current form.

Blankets available.

Do you want to order a certificate form for electrical safety in Samara?

Here you can order the number of forms of certificates you need, made directly to your order, taking into account your wishes and requirements.

The price of the electrical safety certificate form

The cost of the certificate form starts from 40 rubles. and depends on the type of certificate, as well as on the number of ordered certificates.

In addition, our regular partners receive special discounts.

CHANGES,

WHICH ARE INTRODUCED TO THE RULES ON LABOR SAFETY DURING OPERATION

ELECTRICAL INSTALLATIONS APPROVED BY ORDER OF THE MINISTRY OF LABOR OF RUSSIA

1. Clause 1.1 shall be stated as follows:

"1.1. Rules for labor protection during the operation of electrical installations (hereinafter referred to as the Rules) establish state regulatory requirements for labor protection during the operation of electrical installations.

The requirements of the Rules apply to employers - legal entities and individuals, regardless of their organizational and legal forms and employees from among the electrical, electrical and non-electrotechnical personnel of organizations (hereinafter referred to as employees) engaged in the maintenance of electrical installations, conducting operational switching in them, organizing and performing construction, installation, commissioning, repair work, testing and measurement, as well as managing the technological modes of operation of electric power facilities and power receiving installations of consumers.

Safety requirements for the operation of specialized electrical installations, including the contact network of electrified railways, urban electric transport must comply with the Rules, taking into account the operating features due to the design of these electrical installations.".

2. Clause 2.4 shall be stated as follows:

"2.4. Employees related to electrical and electrical engineering personnel, as well as state inspectors exercising control and supervision over compliance with safety requirements during the operation of electrical installations, labor protection specialists who control electrical installations, must pass an examination of knowledge of the requirements of the Rules and other safety requirements for organization and performance of work in electrical installations within the requirements for the relevant position or profession, and have an appropriate electrical safety group, the requirements for which are provided for in Appendix No. 1 to the Rules.

The requirements of the Rules established for employees from among the electrical personnel are also mandatory for employees from among the electrical technological personnel.".

3. The second paragraph of clause 2.5 shall be stated as follows:

"Employees specified in paragraph 2.4 of the Rules and who have passed the test of knowledge of the requirements of the Rules and other safety requirements for the organization and performance of work in electrical installations are issued certificates of knowledge of the rules for working in electrical installations, the forms of which are provided for in Annexes No. 2, 3 to the Rules." .

5. Clause 3.1 shall be stated as follows:

"3.1. Operational maintenance and inspection of electrical installations must be carried out by employees of the subject of the electric power industry (consumer of electric energy) authorized by the subject of the electric power industry (consumer of electric energy) to carry out, in accordance with the established procedure, actions to change the technological mode of operation and the operational state of power transmission lines, equipment and devices with the right to direct impact on the controls of equipment and devices of relay protection and automation in the implementation of operational and technological control, including using remote control facilities, on objects of the electric power industry (power-receiving installations) owned by such a subject of the electric power industry (consumer of electric energy) on the right of ownership or on other legal grounds , or in cases established by law - at electric power facilities and power receiving installations owned by third parties, as well as coordination of the specified actions (hereinafter - operational personnel), or employees from among the repair personnel with the right to directly influence the control bodies of equipment and relay protection and automation devices that carry out operational maintenance of electrical installations assigned to them (hereinafter - operational and repair personnel).

In the Rules, operational personnel are also understood as operational and maintenance personnel, if there are no special requirements for them.

6. Clause 3.4 shall be stated as follows:

"3.4. A sole inspection of the electrical installation, the electrical part of the technological equipment has the right to be performed by an employee from among the operational personnel with a group of at least III, operating this electrical installation, who is on duty, or an employee from among the administrative and technical personnel (managers and specialists), on which is responsible for organizing technical and operational maintenance, carrying out repair, installation and adjustment work in electrical installations (hereinafter referred to as administrative and technical personnel (managers and specialists)), having:

group V - when operating an electrical installation with a voltage above 1000 V;

group IV - when operating an electrical installation with a voltage of up to 1000 V. The right of a sole inspection is granted on the basis of the organization's (separate subdivision) OSD.

Inspection of overhead power lines (devices for transmitting electricity through wires located in the open air, attached with the help of insulators and fittings to supports or brackets and racks on engineering structures (bridges, overpasses) (hereinafter - VL) must be carried out in accordance with the requirements of clauses 7.15 , 38.73, 38.74, 38.75 of the Rules For the beginning and end of the overhead line, linear portals or linear inputs of an electrical installation are accepted, which serve to receive and distribute electricity and contain switching devices, prefabricated and connecting buses, auxiliary devices (compressor, battery), as well as protection devices, automation and measuring instruments (hereinafter referred to as switchgear, switchgear), and for branches - a branch support and a linear portal or a linear input of a switchgear.

7. In paragraphs 3.13, 5.7, 8.1, 14.3, 21.8, 46.6, the words "administrative and technical personnel" in the relevant cases shall be replaced by the words "administrative and technical personnel (managers and specialists)" in the relevant cases.

8. Clause 4.4 shall be stated as follows:

"4.4. Overhaul of electrical equipment with voltages above 1000 V, work on live parts without removing voltage in electrical installations with voltages above 1000 V, as well as repair of overhead lines, regardless of voltage, must be carried out according to flow charts or a work plan (hereinafter referred to as PPR), approved by the head of the organization (separate division).

Work on lines under induced voltage (VL, KVL, VLS, air sections of KVL, which run along the entire length or in separate sections near existing overhead lines or the contact network of an electrified AC railway, on disconnected wires (cables) of which, when grounding the line at the ends (in the switchgear) in its individual sections, a voltage of more than 25 V is maintained at the highest operating current of the influencing overhead lines (when converted to the highest operating current of the influencing overhead lines), are carried out according to technological maps or PPR approved by the head of the organization (separate subdivision).

9. Add paragraph 4.17 with the following content:

"4.17. On overhead lines and overhead lines, before connecting or breaking electrically connected sections (wires, cables), it is necessary to equalize the potentials of these sections. Potential equalization of sections of overhead lines, overhead lines is carried out by connecting these sections with a conductor or by installing grounding on both sides of the gap (proposed gap) with connection to one ground electrode (grounding device).".

10. Paragraphs two and three of clause 5.1 shall be stated as follows:

"registration of work by an order, order or list of works performed in the order of current operation;

issuance of a permit for the preparation of the workplace and for admission to work, taking into account the requirements of paragraph 5.14 of the Rules;".

11. The third paragraph of clause 5.2 shall be stated as follows:

"issuing a permit for the preparation of the workplace and for admission, taking into account the requirements of paragraph 5.14 of the Rules;".

12. Paragraphs 5.3 - 5.6 shall be stated as follows:

"5.3. The employee issuing the order, giving the order, determines the need and possibility of safe performance of work. He is responsible for the sufficiency and correctness of the safety measures indicated in the order (order); for the qualitative and quantitative composition of the team and the appointment of those responsible for the safe performance of work; for compliance groups on electrical safety of employees specified in the work order, the work performed; for conducting targeted briefing to the responsible work manager (foreman, supervisor).

5.4. The right to issue orders and instructions is granted to employees from among the administrative and technical personnel (managers and specialists) who have group V (when operating electrical installations with voltages above 1000 V), group IV (when operating electrical installations with voltages up to 1000 V).

In the absence of workers entitled to issue orders and orders, during work to prevent accidents or eliminate their consequences, it is allowed to issue orders and orders from among the operational personnel who have group IV, located directly on the territory of the electric power facility or the power receiving installation of the consumer of electricity. Granting to operational personnel the right to issue orders and orders must be formalized by the ORD of an organization or a separate subdivision.

5.5. The employee issuing a permit for the preparation of jobs and for admission, answers:

for issuing commands for disconnecting and grounding power transmission lines and equipment under its technological control, and obtaining confirmation of their implementation, as well as for independent actions for disconnecting and grounding power transmission lines and equipment under its technological control;

for the compliance and sufficiency of the measures provided for by the order (order) for disconnecting and grounding equipment, taking into account the actual scheme of electrical installations;

for coordinating the time and place of work of authorized teams, including for accounting for teams, as well as for obtaining information from all teams (allowing) admitted to work in the electrical installation about the complete completion of work and the possibility of putting the electrical installation into operation.

In the event that the employee issuing the permit for the preparation of workplaces and for admission is not the person in whose technological management the power transmission line and equipment are located, the specified employee is responsible for obtaining confirmation of the completed technical measures for disconnecting and grounding the power transmission line and equipment from the dispatching personnel ( an employee of the subject of operational dispatch control in the electric power industry (dispatcher), authorized, when exercising operational dispatch control in the electric power industry, on behalf of the subject of operational dispatch control in the electric power industry, to issue dispatch commands and permits that are mandatory for execution or to change the technological mode of operation and the operational state of dispatching objects, directly influencing them using remote control means, when managing the electric power regime of the power system) or operational personnel, in whose dispatching room or technical logical management is power transmission lines and equipment.

5.6. The right to issue permits for the preparation of workplaces and for admission is granted to operational personnel with a group of at least IV, in accordance with job descriptions.

It is allowed to issue permits for the preparation of workplaces and grant access to employees from among the administrative and technical personnel (managers and specialists) with a group of at least IV, authorized to do so by the ORD of an organization or a separate subdivision.

13. In clause 5.7, the word "SDTU" shall be replaced by the words "dispatching and technological control facilities (hereinafter referred to as SDTU)".

14. Paragraph 5.14 shall be stated as follows:

"5.14. The requirements for the appointment of a person responsible for issuing a permit for the preparation of workplaces and for admission, and for the issuance of such a permit do not apply to the performance of work in electrical installations of consumers of electrical energy, except for work on overhead lines, CL, KVL, requiring coordination by personnel another organization when their operational status changes.".

15. Paragraphs two and three of clause 6.1 shall be stated as follows:

"In cases where the foreman of the work is appointed at the same time as allowing, the order, regardless of the method of its transfer, is filled in two copies, one of which remains with the issuer of the order.

Depending on local conditions, one copy of the order may be transferred to an employee from among the operational personnel who issues permission to prepare the workplace and for admission.

16. In paragraph 6.17 the words "dispatching and technological control facilities (hereinafter - SDTU)" shall be replaced by the word "SDTU".

17. Clause 7.7 shall be stated as follows:

"7.7. When carrying out urgent work, the foreman (supervisor) from among the operational personnel performing work or monitoring those working in electrical installations with voltages above 1000 V must have group IV, and in electrical installations with voltages up to 1000 V - group III. Members of the brigade, working in electrical installations with voltage up to and above 1000 V must have group III.

Admission to work in electrical installations must be carried out after the implementation of technical measures for the preparation of the workplace, determined by the employee issuing the order.

18. The first paragraph of clause 7.15 shall be stated as follows:

"7.15. One employee with group III is allowed to carry out the following work on the overhead line by order:".

19. The second paragraph of clause 17.2 shall be stated as follows:

"In the absence of a visible break in prefabricated switchgears with withdrawable elements, as well as in complete switchgears with SF6 insulation (hereinafter referred to as GIS) with a voltage of 6 kV and higher, it is allowed to check the off position of the switching device by checking the mechanical indicator of the guaranteed position of the contacts." .

20. Clause 18.2 shall be stated as follows:

"18.2. On the drives of the disconnectors, which are turned off to perform work on overhead lines, low voltage lines or CLs, one poster "Do not turn on! Work on the line "regardless of the number of working teams. When remote control of switching devices from the workstation, the sign of the prohibition poster" Do not turn on! Work on the line!" must be displayed on the diagram next to the disconnector symbol that supplies voltage to the power line. If there are no disconnectors on power lines with voltage up to 1000 V, it is allowed to hang out the poster "Do not turn on! Work on the line!" on the drives or control keys of the switching device, depending on its design.

The poster is hung out and removed at the command of the dispatching or operational personnel, in whose dispatching or technological control, respectively, is the overhead line, overhead line or cable line. Before issuing the command to remove the poster "Do not turn on! Work on the line!" dispatching or operational personnel, in whose dispatching or technological control, respectively, is the overhead line, overhead line or cable, must receive from the employee from among the operational personnel issuing permission to prepare the workplace and for admission, confirmation of the completion of work and the removal of all teams from the workplace. ".

21. Paragraphs one and two of clause 19.3 shall be stated as follows:

"19.3. It is allowed to check the absence of voltage by reconciling the circuit in kind:

in outdoor switchgear and at a complete transformer substation (hereinafter referred to as KTP) for outdoor installation, as well as on overhead lines in case of fog, rain, snowfall in the absence of special voltage indicators;

22. In clauses 38.6, 38.88, 41.40, the words "climbing work" in the appropriate case shall be replaced by the words "work performed at a height of more than 5 m from the surface of the earth, ceiling or working platform, on which work is carried out directly from structures or equipment during their installation or repair with the mandatory use of fall protection equipment" in the appropriate case.

23. Paragraphs 38.43 - 38.48 shall be stated as follows:

"38.43. Operating organizations need to determine the lines (sections of lines) under induced voltage by performing measurements, followed by recalculation of the values ​​​​for the highest operating current of the influencing overhead line. The scheme and procedure for measuring the magnitude of the induced voltage and its recalculation for the highest operating current of the influencing overhead line are determined operating organization.

Workers servicing overhead lines must have a list of lines under induced voltage, know the contents of this list and the requirements safe organization and performance of work on them specified in the Rules.

Information about the presence of induced voltage on the overhead line must be indicated in the line "Separate instructions" of the work permit. The value of the calculated induced voltage on the overhead line is indicated in the list of overhead lines under induced voltage.

38.44. All types of work on overhead lines under induced voltage, associated with touching the wire (lightning wire), must be carried out according to technological maps or PPR.

38.45. Work on overhead lines under induced voltage can be carried out by one of the following methods:

with grounding of overhead lines on both sides in the switchgear and at the workplace using the potential equalization technology or the technology of work "without stress relief" to ensure the safe performance of work;

without grounding the overhead line in the switchgear when grounding the overhead line only at the workplace.".

38.46. Work with grounding of overhead lines on both sides in the switchgear and at the workplace using potential equalization technology should be carried out with the following measures:

the overhead line brought out for repair must be grounded on both sides in the switchgear;

when working from a metal support at the workplace of the brigade, the phase wires (ground wire) of the overhead line must be grounded to the support post, and when working from a reinforced concrete support - to a stationary ground electrode that is in good working order and meets the established requirements;

when working from a telescopic tower (hoist), the working platform of the tower must be connected to the wire (cable) of the line with a flexible conductor with a cross section of at least 25 mm2, and the tower (chassis) itself must be grounded. The wire (ground wire) of the line must be grounded at the work site. It is not allowed to get in and out of the telescopic tower cabin, as well as touch the tower body while standing on the ground after connecting the working platform of the telescopic tower with the wire.

During operation, it is not allowed to use ropes made of conductive materials as "endless" ropes.

The number of teams allowed to work on the overhead line, working according to the method specified in this paragraph of the Rules, is not limited.

If it is impossible to ensure equalization of potentials at the workplace (for example, when working from a wooden support), work must be performed in accordance with paragraphs 38.47 or 38.48 of the Rules.

38.47. Work with grounding of overhead lines on both sides in the switchgear and at the workplace using the "without voltage relief" technology must be carried out with the implementation of the measures provided for in paragraphs 38.21 - 38.32 of the Rules.

38.48. Work without grounding the overhead line in the switchgear when grounding the overhead line only at the workplace should be carried out with the following measures:

the overhead line brought out for repair from the side of the switchgear is not grounded;

no more than one team may be allowed to work on one overhead line (on one electrically connected section);

The overhead line (section of the overhead line) is grounded only in one place (at the place of work of the brigade) or on two adjacent supports. At the same time, at the place of work of the brigade, in addition to the main one, it is necessary to install additional portable grounding. When removing portable grounding at the end of work, it is first necessary to disconnect the clamps of both groundings from the wire (lightning cable) of the overhead line, and then from the ground electrode. It is allowed to work only from a support on which grounding is installed (main and additional), or in the span between adjacent grounded supports;

if it is necessary to work in two or more spans (sections), the overhead line must be divided into electrically unconnected sections by disconnecting the loops on the anchor supports. Only one team can work on each of these sites;

before installing or removing grounding, the wire (cable) must be preliminarily grounded using a rod with an arc extinguishing device (to remove the static component of the induced voltage and localize the arc discharge). The grounding wire of the rod must be connected to the grounding conductor in advance. The bar can be removed only after the installation (or removal) of the portable grounding;

in the absence of a rod with an arc extinguishing device, installation (removal) of protective grounding at the workplace can be carried out only after temporary grounding of the overhead line in one of the switchgears. Grounding knives at the end of the overhead line in the switchgear should be turned off only after the installation (removal) of grounding at the workplace.

24. Supplement the Rules with new paragraphs 38.49 - 38.50 of the following content:

"38.49. On the overhead line (in one electrically connected section) under induced voltage, simultaneous work of teams using different methods of work specified in paragraph 38.45 of the Rules is not allowed.

38.50. On overhead lines under induced voltage, work from the ground associated with touching a wire (cable) lowered from a support down to the ground should be carried out using electrical protective equipment (dielectric gloves, rods) or from a metal platform connected by a conductor to this wire (cable) for potential equalization. The connection of a metal platform with a wire (cable) should be carried out using electrical protective equipment and only after the worker is located on it. Approaching the site without means of protection against step voltage is not allowed.

Performing work from the ground without the use of electrical protective equipment and a metal platform is allowed provided that the wire is grounded in close proximity to each point of contact.

"38.51. When installation work(lifting, sighting, stretching, transferring wires from rolling rollers to clamps) on overhead lines under induced voltage or under construction overhead lines in the alignment of existing overhead lines, the wire must be grounded on the anchor support from which the rolling is carried out, on the final anchor support through which the tension is carried out, and on each intermediate support on which the wire is raised.

38.52. Upon completion of work on the intermediate support, the grounding from the wire (lightning cable) on this support can be removed. In the event of resumption of work on an intermediate support associated with touching the wire (lightning cable), the wire must be grounded again on the same support.

38.53. Steel traction ropes used when installing wires on overhead lines under induced voltage must first be fixed on the traction mechanism and grounded to the same ground electrode as the wire to equalize the potentials. Only then is it allowed to attach the rope to the wire. It is possible to disconnect the wire and the traction rope only after equalizing their potentials, that is, after connecting each of them to a common ground electrode.

38.54. On overhead lines under induced voltage, the transfer of wires from rolling rollers to supporting clamps should be carried out in the direction opposite to the rolling direction. Prior to the beginning of the relocation, it is necessary, leaving the grounded wires on the anchor support, towards which the relocation will be carried out, to remove the grounding from the wires on the anchor support, from which the relocation begins.

Grounding from the relocated wires (cable) can only be removed after the wire (cable) has been transferred to the supporting clamps and work on this support has been completed.

38.55. During the transfer of wires to the clamps, the adjacent anchor span, in which the transfer has already been completed, should be considered as being under induced voltage. It is allowed to carry out work on it related to touching the wires only after grounding them at the workplace.

27. In paragraphs 38.88, 40.7, 46.2 the words "norms and" shall be deleted.

28. In paragraph 41.36, delete the word "legal".

29. In clause 45.1 the words "In electrical installations" shall be replaced by the words "In existing electrical installations".

30. The first paragraph of clause 45.3 shall be stated as follows:

"45.3. The passage of cars, hoisting machines and mechanisms through the territory of the outdoor switchgear and in the security zone of the overhead line should be carried out under the supervision of one of the employees from among the operational personnel, the employee who issued the order or the responsible manager, and in electrical installations with voltage up to 1000 V - the foreman who has group IV, when performing construction and installation work in the security zone of the overhead line - under the supervision of a responsible manager or foreman who has group III.".

31. Clause 46.5 shall be stated as follows:

"46.5. Granting the seconded personnel the right to work in existing electrical installations as issuing orders, responsible managers and foremen who allow members of the brigade on overhead lines in accordance with paragraph 5.13 of the Rules, members of the brigade are allowed to issue the head of the organization (separate subdivision) - the owner of the electrical installation, with a resolution in the letter of the sending organization or ORD of an organization (separate subdivision).".

32. Paragraph 6 of the notes to Appendix No. 1 shall be stated as follows:

"6. State inspectors exercising control and supervision over compliance with safety requirements during the operation of electrical installations must have a group of at least IV.

Labor protection specialists who control electrical installations of electric power consumer organizations must have group IV, their work experience (not necessarily in electrical installations) must be at least 3 years.

Labor protection specialists of electric power industry entities that control electrical installations must have group V and are allowed to perform official duties in the manner established for electrical personnel.

The form of the certificate issued to state inspectors and labor protection specialists is given in Appendix No. 3 to the Rules.".

33. In Appendix No. 2:

a) set out the form of the certificate of knowledge of the rules of work in electrical installations in new edition:

# New forms of certificates 2016

sample of a new electrical safety certificate 2016

b) state the notes in the following wording:

"1. A certificate of knowledge of the rules of work in electrical installations (hereinafter referred to as the certificate) is a document certifying the right of the bearer to independent work in the specified position.

2. The certificate is issued to the employee when applying for a job and is valid only after the relevant records on the results of checking knowledge of the rules for working in electrical installations, assigning an electrical safety group.

3. Second page of the certificate:

in the column "Admitted as" the category of personnel is indicated: administrative and technical (managers and specialists), dispatching, operational, operational and repair, maintenance personnel, etc.;

the column "to work in electrical installations with voltage" is filled in after checking the knowledge for employees admitted in accordance with the ORD of an organization or a separate subdivision to perform work or organize the safe performance of work in electrical installations indicating the voltage class (up to 1000 V, up to and above 1000 V) .

4. The third page of the certificate contains a general assessment of the results of the knowledge test. The page is not filled in if an employee of the electric power industry organization conducts an extraordinary knowledge test in one of the following sections: device and technical operation, labor protection, fire safety.

5. The fourth, fifth and sixth pages of the certificate are filled out for employees of power industry organizations and contain assessments of the results of knowledge testing normative documents according to the divisions: device and technical operation, labor protection, fire safety.

6. The seventh page is filled out for employees who, according to their official duties and nature production activities a test of knowledge of industrial safety rules and other special rules is required.

7. The eighth page is filled out for workers allowed to conduct special works (works performed at a height of more than 5 m from the ground, ceiling or working platform, on which work is carried out directly from structures or equipment during their installation or repair with the mandatory use of fall protection equipment, testing, etc.).

8. The certificate must always be with the employee during the execution of official duties and presented at the request of supervising employees.

9. The certificate is subject to replacement in case of a change in position.

10. The certificate consists of a hard cover and a block of pages. In the certificate for consumers of electric energy, the presence of the fourth, fifth and sixth pages, as well as the obligation to have a photograph, is not required. The size of the certificate is 95 mm x 65 mm. The preferred binding color is dark cherry.

11. On the front side of the cover there is the inscription "Certificate", which must be replaced by a contrasting (white or yellow) color.".

34. In Appendix No. 4:

a) in the title the word "PROTOCOL" shall be replaced by the words "PROTOCOL N ___";

b) the words "position (profession)" shall be replaced by the word "position";

c) the words "approved for work as _______________________" shall be replaced by the words "approved as "**" ________________ for work in electrical installations with voltage "***" ____________";

d) the designation of the footnote "**" shall be replaced by "****";

e) footnotes shall be stated in the following wording:

""*" Indicated for dispatcher, operational and operational and maintenance personnel.

"***" The voltage class is indicated (up to 1000 V, up to and over 1000 V) for workers admitted to the direct performance of work in electrical installations.

"****" Signs if he participates in the work of the commission.".

You can quickly understand the changes brief analysis of changes in a convenient form

In 2018, Rostekhnadzor published an instruction that prohibited training centers from testing knowledge and issuing electrical safety certificates. It is now possible to obtain a document confirming an electrical safety group for certain categories of employees only at Rostekhnadzor. We will tell you who belongs to this category, how to prepare for the knowledge test. Find out how the old ID is different from the 2019 ID.

Who needs to have an electrical safety certificate

The electrical safety certificate is binding document, which confirms that the employee has successfully passed the knowledge test and has a certain group of access to work in electrical installations.

Certificate of knowledge of the rules of work in electrical installations must have:

  • employees who belong to electrical and electrical personnel (according to form No. 2)
  • labor protection specialists controlling electrical installations (according to form No. 3)
  • state inspectors who exercise control and supervision over compliance with safety requirements during the operation of electrical installations (in form No. 3)

This rule has been in effect since the entry into force of the Order of the Ministry of Labor of Russia dated February 19, 2016 No. 74n, which amended paragraph 2.4 of the Order of the Ministry of Labor of Russia dated July 24, 2013 No. 328n.

It was

It became

Important! The main thing that employers should know and take into account is that from June 29, 2018, Rostekhnadzor banned training centers from testing knowledge and assigning electrical safety groups. Now you can pass the electrical safety exam and get a certificate with a tolerance group only at Rostekhnadzor (Rostekhnadzor letter No. 00-08-05 / 388 dated 06/29/2018). You can get training in training organizations, but you can only pass the test at Rostekhnadzor. Rostekhnadzor inspectors are prohibited from participating in the work of the commissions of training organizations.

Electrical safety certificate form

There are currently two approved forms of electrical safety certificates:

  1. On testing knowledge of the rules of work in electrical installations (form No. 2).
  2. On checking the knowledge of the rules by employees who control electrical installations (form No. 3).

The order of the Ministry of Labor of Russia dated February 19, 2016 No. 74n approved not only amendments to order No. 328n, but also introduced a new form of certificate “On testing knowledge of the rules for working in electrical installations”.

How is it different from the previous one?

  1. The first and most important difference is that the new form of the certificate provides a place for the employee's photo.

Note! In the certificate for consumers of electrical energy the presence of the fourth, fifth and sixth pages, as well as the obligatory presence of a photograph, is not required. This applies only to electric power companies.

2. New ID consists of 8 stations, and not from 4 as before.

3. Employee data in the new form of electrical safety certificate indicate on the first two pages, not on one. Their list included the name of the structural unit in which the employee is listed.

4. On the second page of the certificate in the column " » indicate the category of personnel: administrative and technical (leading employees and specialists), dispatching, operational, operational and repair, maintenance personnel, etc.

5. Also on the second page, the column " To work in electrical installations with voltage» fill out after a knowledge test for employees admitted to work or to organize the safe performance of work in electrical installations indicating the voltage class (up to 1000 V, up to and above 1000 V).

6. Now there are 5 pages instead of 2 for recording the results of regulatory document knowledge checks. Please note that not all of these pages need to be filled out by Consumer companies. See note to form #2.

  • Results of testing knowledge of regulatory documents (3 pages)
  • The results of testing knowledge of regulatory documents on the device and technical operation (4 pages)
  • The results of testing knowledge of normative documents on labor protection (5 pages)
  • The results of testing knowledge of regulatory documents on fire safety(6 pp.)
  • The results of testing knowledge of regulatory documents on industrial safety and other special rules (7 pages)

Note! Employees often ask if they can continue to use the previously obtained certificate when moving to a new job. The answer to this question is clear - can not! The certificate indicates the specific company in which the employee works. When dismissed, the document becomes invalid. Therefore, if labor contract was terminated, and then concluded again, at least the next day, the employer again has an obligation to train staff. But at the same time, the duration of the internship can be reduced by the decision of the mentor, but not less than 2 days.

Where and how to get an electrical safety certificate

Before obtaining an electrical safety certificate, an employee must undergo training. You can prepare yourself, in your company or.

Documents on the basis of which electrical safety certificates are issued:

  • members of commissions for knowledge testing within organizations
  • responsible for electrical equipment of consumers and their deputies
  • labor protection specialists whose duties include monitoring electrical installations
  • employees, if the number of employees in their organization does not allow the formation of a commission

The rest of the staff can be trained directly in their organization. To do this, the head of the company creates special commission, which should include at least five people (clause 1.4.30 of the Rules for the technical operation of electrical installations of consumers, approved by order of the Ministry of Energy dated 13.01.2003 No. 6).

The chairman of the commission must have an electrical safety group:

  • Group V, if the company operates electrical installations with voltage up to 1000 V and above;
  • Group IV, if the company operates electrical installations with voltage up to 1000 V only.

All members of the commission must have an electrical safety group and pass a knowledge test at the Rostekhnadzor commission, but PTEEP allows three commission members to be examined at Rostekhnadzor, of course, the chairman and deputy, as well as an OT specialist. The remaining two members of the commission can be checked in your own commission.

If an employee has only a school certificate and no secondary vocational education, then it is possible to assign him even the lowest electrical safety group after his training in training center on . After this training, the employee can take an exam. You can not assign groups not in chronological order, as well as violate the terms of service in certain groups.

For the conditions for assigning an electrical safety group to electrical (electrotechnological) personnel, see the table at the end of the article.

Validity period of the electrical safety certificate

The electrical safety certificate is valid until new check knowledge - after 1 year or after 3 years (clause 1.4.20 of the Rules for the technical operation of electrical installations of consumers, approved by order of the Ministry of Energy dated 13.01.2003 No. 6).

  • 1 year for electrical personnel directly organizing and carrying out maintenance work on existing electrical installations or performing adjustment, electrical installation, repair work or preventive tests in them, as well as for personnel entitled to issue orders, orders, conduct operational negotiations
  • 3 years for administrative and technical personnel not belonging to the previous group, as well as for labor protection specialists admitted to inspect electrical installations

An employee also needs to obtain a new electrical safety certificate if:

  • The position has changed, and the employee needed new knowledge on the operation of electrical installations
  • Moved to a new place of work (to a new employer)
  • Lost or damaged form
  • Passed advanced training
  • There was a break in work for more than 6 months
  • The company put into operation new equipment
  • Electrical safety rules have changed

You can get theoretical knowledge and practical experience in electrical safety of groups 2-5.

A certificate in the field of electrical safety is the main document that confirms the authority of an employee to perform special types of work. In the process labor activity using industrial electrical engineering, the employee must have this document. His absence is regarded as a serious violation, for which the employer will have to pay a large fine. In exceptional cases, the work of the company may be suspended for a period of up to 90 days.

New electrical safety certificate form 2016: download or buy

Currently, Russia uses a sample certificate, which entered into force in 2016. It was introduced by order of the Ministry of Labor No. 74n, which made a number of additions and clarifications to the content of the main order of the department No. 328n. At present, the current version of the certificate is contained in Appendix No. 2 to the latest document.

A company that needs to issue certificates for its employees can choose one of two ways to solve this problem:

  • buy ready-made forms of documents and enter the necessary information about employees into them;
  • independently download the certificate form, print it, provide a cover and fill it out.

Where to download the certificate form for electrical safety-2016 in Word

The question of where exactly you can find the required sample is not particularly difficult. It is contained in all official versions of Order No. 328n posted on serious web portals. For example, such a form can be downloaded for free on our website. This option is suitable for large companies, because it allows you to save money when preparing necessary documents a lot.

It should be borne in mind that, along with the documents of the new sample, the certificates of the old format still remain valid for the entire period of their application. Recall that in accordance with paragraph 1.4.20 of the order of the Ministry of Energy No. 6, it can be from one to three years. If during this period the employee continues to work in the organization that issued the certificate, there is no need to change it. However, if the specialist changed jobs during the validity period of the certificate, it will have to be obtained again. To do this, the employee will have to re-certify and confirm their knowledge of electrical safety.


Related Articles

Latest Articles
Popular Articles
Editor's Choice
oddagipermarket.ru